redcrowd78

How to Replace a Saab 9-3 Key The Saab 9-3 has a great attraction for drivers. It is powerful and has excellent visibility. It has a very high safety rating. It is essential to have two keys that work for your vehicle. If you lose one key, it can be very expensive to add a new one. How to replace the ignition Key in the Saab9-3 You'll need to replace your car keys in case it isn't turning. This guide will walk you through the steps to do it on a Saab 9-3. You will have to replace the key, buy another reprogrammable device, and buy a brand new case for your key-fob. Contrary to earlier models, modern Saab cars use a transponder in the key-fob rather than a physical key that can be used to unlock and start the car. The rechargeable batteries contained in the key-fob will eventually become worn out and cannot hold any charge. This is especially applicable if you are using the same key for the same lock. A professional locksmith can replace the battery quite easily. You can also do it yourself if you have the right tools and a bit of patience. The first step is to remove the key-fob apart. This is accomplished by inserting a flathead screwdriver in the slot located in the middle of the case. It is important to work slowly, as the plastic is very thin and easily damaged. Once the case is opened and the case is opened, you can make the new key by combining the lower portion of the key that was used previously with the transponder and banana on the new key. This will ensure that the new key is mated to the CIM properly, which can make all the difference when replacing the primary key for your Saab 9-3. How do you replace the ignition Key on a Saab 900 If you do not have two keys, you will have to take off the dashboard and steering wheel to gain access to the ignition. Start by disconnecting the negative battery cable. Once the battery is disconnected, you can take off all the trim pieces and dashboard pieces that surround the steering wheel. Once the dashboard is removed, insert screws into the hole behind the ignition switch. The ignition barrel has key locks that can prevent the vehicle from starting if the key isn't inside it. If the ignition switch on your 900 isn't working properly, check the key to determine whether it's in the lock or is stuck in the barrel of the ignition. It is also important to rotate your keys and keep them clean to prevent bent. Saab cars differ from other cars in that they do not use traditional metal keys. Instead, the car detects the electric signals of the key fob by a specific chip inside it. If you lose your sole working key fob, the dealer will charge you top dollar to replace your computer module (known as the CIM). We can reprogram the EEPROM on your current computer to make it accept new keys without the need to replace it. You'll save up to 50% on the price charged by the dealer! This is the SAAB KEY PROGRAM. Learn more about it here! How to replace the ignition Key on a Saab 9-5 The metal portion of a classic Saab key is simple to copy, and is also not much of a deterrent against theft of a vehicle. The real security comes from the electronic part inside the key-fob. G28 is equipped with a chip that recognizes your car when it's put into the ignition switch. Saab has relied on the technology of this anti-theft device for over a decade. It's not as secure as a physical lock on the door however it makes stealing your own car significantly harder. That's why every Saab owner should always keep an extra key in their possession. Most new Saabs come with two keys in the factory, but you can buy more keys from a dealer through a special handheld computer known as Tech-2. Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this is the NG 9-3 cars, which have more modern, more advanced features that require the use of a key-fob. The dealer will replace the CIM or TWICE module in those cars if keys have been lost, and charge you top dollar to do it. We can reprogram your computer's EEPROM to accept new keys, without replacing expensive modules. How to replace the ignition Key on an XC90 Saab If your SAAB 9-3 key fob is having problems turning the barrel of the lock it's possible that it's time to replace it. The process is simple and you don't even need to visit a dealer. Instead, you can do it yourself at home, using just some basic tools. In the beginning, you'll need to prepare the new key. Before you begin, turn off the anti-theft system by placing blocks underneath your rear wheels, and then releasing your handbrake. Insert the key in the ignition and turn the key to the “on” position. This will activate the accessories, but will not start the engine. Repeat this procedure five times, then leave the key in the on position. The next step is to find a new case for your old key fob. They can be found at a variety of auto parts stores and are usually very affordable. Depending on the model, you could even get them without any electronics. To open the case, gently push the flathead screwdriver into the slot in the middle. The case should split easily and, once you've got it open, you'll get access to the internal electronics. Use a flathead screwdriver, which will gently pry open the electronic components.